TruXedo TruXport Tonneau Cover 298301
We designed the TruXport 298301 to deliver professional-grade truck bed protection without the bulk or complexity of hard folding covers. This soft roll-up tonneau cover combines weather-resistant MaxLife fabric with a low-profile aluminum frame that installs in minutes using nothing but a ratchet.
Whether you’re securing tools for the jobsite or weekend camping gear, the TruXport keeps your cargo dry and out of sight. Our dual-latch system creates a weather-tight seal along the entire perimeter, while the tension control system ensures a drum-tight appearance mile after mile. When you need full bed access, the cover rolls toward the cab and secures with integrated buckle straps—no removal required.
- MaxLife fabric with marine-grade thread resists UV rays, mildew, and tearing
- Low-profile aluminum bow frame adds strength without reducing bed clearance
- Fits 2015-2023 Chevrolet Colorado / GMC Canyon 5′ bed (60.5″)
- Dual-position Lever Latch provides secure lock-down at cab or tailgate
- Tension control adjustment system maintains tight appearance in all weather
MaxLife Fabric & Frame Construction
The heart of the truxedo truxport tonneau cover 298301 is our proprietary MaxLife material—a vinyl-coated fabric bonded with marine-grade polyester thread. This combination resists cracking in sub-zero temperatures and stays supple through desert summers. Unlike cheaper vinyl covers that fade to chalky white after two seasons, MaxLife retains its deep black finish year after year.
Aluminum Bow Architecture
We reinforce the cover with seven powder-coated aluminum bows spaced evenly across the bed length. Each bow locks into side rails with a positive-grip channel system that prevents lateral movement during highway driving. The frame sits just 1.5 inches above the bed rails, preserving your truck’s sleek profile and allowing the tailgate to close fully with the cover in place.
Fit Specifications for Colorado & Canyon Trucks
This 298301 model fits 2015 through 2023 Chevrolet Colorado and GMC Canyon models equipped with the 5-foot short bed (actual bed length 60.5 inches). Our clamp-on installation system works with factory bed rail caps and most aftermarket bed rail systems—no drilling, cutting, or permanent modification required.
Bed width compatibility ranges from 57.8 to 58.2 inches between the inner bed walls. If you’ve installed a spray-in bed liner, confirm that it doesn’t extend above the bed rail cap; our clamps seat against the top surface of the rail for proper tension.
Operating Your TruXport Daily
Full bed access starts with releasing both Lever Latches at the tailgate. Roll the cover forward toward the cab, gathering the fabric around the front bow. Secure the rolled cover using the three quick-release buckle straps sewn into the underside—two attach to the side rails, one wraps over the top.
For partial access, release only the tailgate latch and roll the cover forward to your desired position. The tension control adjustment (located inside each side rail near the cab) lets you fine-tune fabric tightness. Turn the adjuster bolt clockwise to increase tension if you notice sagging; counterclockwise to reduce tension if the fabric feels stretched.
Complete Your Truck Bed Protection
What people are saying
TruXport 298301 Buyer Questions
Yes, the TruXport installs over most spray-in bed liners including Line-X, Rhino Lining, and Herculiner. The clamps must seat on top of your bed rail caps, so confirm that your liner application didn’t overspray onto the rail cap surface.
If liner material extends above the rail, you may need to trim it back slightly for proper clamp contact. Drop-in plastic bed liners are also compatible—the clamps grip the liner’s molded rail caps.
Yes, the truxedo truxport tonneau cover 298301 is rated for touchless and soft-brush automatic car washes when both latches are secured. The weather seal system handles the water pressure from standard car wash equipment.
Avoid high-pressure wand washes directed at the seams, and never use coin-op pressure washers at close range. After washing, check that the fabric tension remains tight and adjust if needed using the side rail adjustment bolts.
The TruXport is not designed to support standing weight or heavy loads on top of the fabric. You can brush off light snow accumulation (up to 2 inches), but remove heavier snow before it compacts.
The cover is engineered to protect cargo inside the bed, not to serve as a cargo platform. Placing items on top of the cover can stress the fabric and bows, potentially voiding your warranty.
The TruXport 298301 requires clear access to the bed rail caps along the full length of the bed. Most bed extenders that mount inside the bed or attach to the tailgate are compatible, as long as they don’t interfere with the side rail clamps.
Bed rack systems that mount to the rails (like Thule or Yakima) will conflict with the TruXport’s clamp positions. You’ll need to choose between the rack system and the tonneau cover, or consider a cover designed to integrate with rail-mounted accessories.
Each side rail has a tension adjustment bolt located near the cab end, accessible from inside the bed. Use the included allen wrench to turn the bolt clockwise—this pulls the fabric tighter toward the cab.
Make small adjustments (quarter-turn increments) on both sides equally to maintain even tension. After adjusting, roll and unroll the cover once to redistribute tension across all bows. Check tension every few months, especially after temperature swings.
We offer a 30-day fit guarantee from the date of purchase. If the TruXport 298301 doesn’t fit your 2015-2023 Colorado or Canyon 5′ bed due to a manufacturing error, contact our customer service team for a prepaid return label.
The cover must be in new, resalable condition with all hardware and packaging. Custom orders or covers that have been installed and used for more than 30 days are not eligible for return, but remain covered under our 5-year warranty for defects.
Most customers install the truxedo truxport tonneau cover 298301 solo in 20-30 minutes. The cover ships partially assembled on its frame, so you’re not building components from scratch.
The main steps are positioning the frame on the bed rails, hand-tightening eight clamps, and mounting the two latches to the side rails. A second person can help align the frame initially, but isn’t necessary. The only tool required is the included allen wrench (or a ratchet with 10mm socket speeds up clamp tightening).